Re: [Re: [Re: [uCsimm] ethernet connectivity problem]]

From: Richard Sevenich (rsevenic@netscape.net)
Date: Tue Jul 18 2000 - 13:29:19 EDT


Thanks to all who responded to my plea for help on the
ethernet connectivity problem - particularly Phil and David.
I got to my office this morning, replaced the laptop's
brand new ethernet card with an older known card - and
everything works now. I can ping and nsf mount with joy.

Thanks again,
Sev

David Smead <smead@amplepower.com> wrote:
> You need a default route = eth0.
>
> Sincerely,
>
> David Smead
> http://www.amplepower.com.
> http://www.ampletech.com.
>
> On 17 Jul 2000, Richard Sevenich wrote:
>
> > route command gives:
> >
> > destination gateway genmask flags metric ref use iface
> > 192.168.1.11 * 255.255.255.255 UH 0 0 0 eth0
> > 192.168.1.0 * 255.255.255.0 U 0 0 0 eth0
> > 127.0.0.0 * 255.0.0.0 U 0 0 0 lo
> >
> > No gateway to ISP, just have the two machines interconnected.
> >
> > The uCsimm has IP 192.168.1.200 at the moment.
> >
> > I've also tried
> > laptop IP = 192.168.1.1
> > since the uCsimm would see that as its gateway.
> >
> > Thanks,
> > Richard
> >
> > Phil Wilshire <philw@zentropix.com> wrote:
> > > Richard
> > > lets see the output from the
> > > "/sbin/route"
> > >
> > > command.
> > >
> > > mine is...
> > > [philw@bierk philw]$ /sbin/route
> > > Kernel IP routing table
> > > Destination Gateway Genmask Flags Metric Ref Use
> > > Iface
> > > 192.168.2.231 * 255.255.255.255 UH 0 0 0
> > > eth0
> > > 192.168.2.0 * 255.255.255.0 U 0 0 0
> > > eth0
> > > 127.0.0.0 * 255.0.0.0 U 0 0 0
> > > lo
> > > default 192.168.2.100 0.0.0.0 UG 0 0 0
> > > eth0
> > >
> > > where the default line 192.168.2.100 is a Moreton Bay 2500 acting as an
> > > ISP gateway.
> > >
> > > you may need to
> > >
> > > /sbin/route add -net 192.168.2.0 netmask 255.255.255.0 dev eth0
> > >
> > > Regards
> > > Phil Wilshire
> > > >
> > > > Another newbie question for my new uCsimm setup.
> > > >
> > > > I have serial communication established between my laptop and the
uCsimm
> > > > which is on the uCgardener. I now want to establish the ethernet
> > connection.
> > > > Both the uCsimm and laptop recognize their respective ethernets, each
has
> > a
> > > > different IP address on the same subnet etc., each can ping itself by
the
> > > > proper IP - but neither can ping the other. I believe I have the
> > respective
> > > > machines set up properly, but perhaps there
> > > > is something I've missed. Any hints?
> > > >
> > > > The laptop's ethernet pcmcia card is new, so it could have a RJ45
> > connector
> > > > problem I suppose. The two machines are connected by a crossover
cable,
> > but I
> > > > also tried with regular cables and my hub.
> > > >
> > > > I would appreciate hints/advice.
> > > >
> > > > TIA,
> > > > Sev
> > > This message resent by the ucsimm@uclinux.com list server
> > http://www.uClinux.com/
> >
> >
> > ____________________________________________________________________
> > Get your own FREE, personal Netscape WebMail account today at
http://webmail.netscape.com.
> > This message resent by the ucsimm@uclinux.com list server
http://www.uClinux.com/
> >
>
> This message resent by the ucsimm@uclinux.com list server
http://www.uClinux.com/

____________________________________________________________________
Get your own FREE, personal Netscape WebMail account today at http://webmail.netscape.com.
This message resent by the ucsimm@uclinux.com list server http://www.uClinux.com/



This archive was generated by hypermail 2b30 : Sun Apr 07 2002 - 00:01:37 EST